Detailed Product Description

INPUT VOLTAGE:DC8--18V
ATARTING UP INSTANT VOLTAGE:AC23000 V
STEADY POWER:35W
ELECTRIC EFFICIENCY>0.82
AMBIENT TEMPERATURE:-40C~150C
USEFUL LIFE>3500H

The ballast is the most important part of a HID xenon conversion kit.

Every ballast left factory must pass the test as follow.

1, lights a lamp the start test
A, input standard voltage 12.8V lightens when the light bulbshould not have the scintillation.
B, input standard voltage 12.8V lightens when the light bulb coldstart the instantaneous electric current should about 6.5;
C, input standard voltage 12.8V lightens when the light bulb hot startthe instantaneous electric current should not surpass 8A.
2, instantaneous high/low voltage charging protection test
A, the stabilizer is between 8-22v all can normally start(voltage error in the input voltage establishment to be supposed in±1v within);
B, when the input voltage is lower than 8v or is higher than 22v thestabilizer to be supposed the automatic knock off (voltage error to besupposed in ±1v within);
C, when the input voltage restores to below 8v above or 22v thestabilizer should be possible the self-recovery work (voltage error tobe supposed in ±1v within)
3, installment protection test
A, when the stabilizer has not met the light bulb, when is atthe light condition, the stabilizer should the automatic knock off,avoid the high-voltage injury.
4, short-circuits the protection test
A, the stabilizer when the out-port for short-circuits shouldthe knock off automatic protection, the stabilizer not damage.
5, ties hands behind the back the protection test
A, the stabilizer when inputs the power source cathode meetscounter- should the knock off automatic protection, the stabilizer notdamage.
6, permanent power test
A, when input voltage when 8-22v, the stabilizer output mayconstantly maintain at 35W (deviation positively and negatively doesnot surpass 3W) about, protects HID not to damage.
7, 1m/ inferior power failure test
A, the stabilizer continuously 100,000 power failures/electriclamps movement may not appear the breakdown; In the production thetest should the continual power failure/electric lamp test 500 timedoes not crash.
8, high low temperature ambient temperature work test
A, the stabilizer under -40 ~ +,150 ambienttemperatures may the normal long-firing operation.
9, fast starts the performance test
A, mains input voltage for standard voltage 12.8v when startsthe electric lamp voltage not to be smaller than actual approximately6.5A, causes to meet the xenon lamp in to start in for a second, thelight well-illuminated achieved the standard brightness 20%, in 4seconds lights through Quantity  achieves the standard brightness 80%.
10, long time electric lamp experiment
A, the stabilizer must achieve continuously uninterruptedlights a lamp with the storage battery mains input for 24 hours not tohave the breakdown
B, must achieve continuously every day 12 hours, theaccumulation continuously 10,000 hours do not have the breakdown.
11, work Temperature rise
A, the stabilizer should conform to constantly the activestatus undersurface Temperature rise not to be possible to surpass 40.
12, quakeproof test
A, under active status stabilizer on vibration experimentmeter by frequency 10-45Hz, under oscillation amplitude 2-10mmvibration environment, X/Y/Z axis three directions 8 hour haven't whatbreakdown;
B, the stabilizer does not have in any packing situation in themonomer after the hard ground 1 meter go down, should be allowedto continue the normal work.
13, waterproof dustproof test
A, will connect the good power source and the light bulbstabilizer soaks in the water the continuous working 24 hours does nothave the breakdown.
14, anticorrosion test
Slightly
15, radiated interference test
A, when actual use the automobile FM receiver appears (radiowithout the static to be away from a stabilizer approximately meter).The stabilizer is smaller than -90DB to the radio jamming to besmaller than 5 microwatts;
B, instead fills the electric current disturbance: The stabilizerworks when does not surpass 300mV in the wiring place with theoscilloscope survey ripple, actual approximately is 150mV-250mV.(Avoids disturbing on automobile other electric appliances work)

Quality guarantee: One year unconditional quality warranty!